Click here to sign in with or

by Eindhoven University of Technology

Extrusion using a gear pump is useful in production processes where temperatures must remain low, for example in the automotive industry to produce car tires. At too high temperatures, material properties change, becoming rigid and less fluid and therefore block the pump. Ph.D. candidate Vincent de Bie has developed a numerical simulation to better understand and predict the effect of fluid properties. This makes it easier to experiment with such manufacturing processes via a computer, reducing the amount of material that needs to be processed to achieve an airtight tire.

Extrusion is a high-volume manufacturing process that is used for materials such as food, concrete, metal, and polymers. In sheet film extrusion, a strip is extruded that typically has a high width over height ratio. This is for example used in the automotive industry to produce car tires.

An external gear pump is sometimes added to the extrusion systems, to increase the pumping capabilities. A drawback of using this pump is the often observed fluctuation in the output. By numerically studying an external gear pump processing high-viscosity fluids using the finite element method, De Bie observed that besides the gear geometry, fluid properties strongly affect the output of the pump.

Fluctuation in the output of pumps

In the external gear pump, the separation of the gears creates a vacuum, which results in suction of the fluid into this space. The fluid is then trapped in the inter-teeth volumes when these are closed off by the casing of the pump. Within these volumes, it is transported to the other side of the gears.

Due to the intermeshing of the gears, the fluid is pushed out of the external gear pump. A high pressure is often observed at the exit, since the fluid is typically pushed through a narrow die opening. Many studies showed that a fluctuation is present in the output of the pumps.

This so-called ripple is mainly the result of the geometry of the gears, and thus its frequency is related to the number of teeth of a gear. Obviously, a ripple in the output is undesired, since this results in inconsistent dimensions in an extrusion process. Several studies attempted to numerically predict this ripple. However, most studies consider Newtonian fluids and turbulent flow. In a polymer extrusion process, the flow is typically laminar and fluid properties depend on deformation rate, pressure and/or temperature.

The goal of De Bie's research was to perform fluid flow simulations of the external gear pump for high-viscosity fluids. He developed a numerical simulation using the finite element method, where the fluid model can be varied. De Bie and his research group wanted to understand the effect of fluid properties on the ripple and the efficiency of the pump. Therefore, they studied the effect of including a deformation-rate, pressure, and temperature dependence of the fluid properties.

To enable application of the simulations in the automotive industry, the reaction process of rubbers, i.e. vulcanization, is even modeled. Local (pre-)vulcanization during rubber extrusion can now be visualized. For these curing fluids, the residence time in the pump should be as low as possible. For this reason, the residence time can also be tracked using a convection equation or by particle tracking.

Using 2D simulations, De Bie showed that the efficiency of the pump drops for low rotation speeds, fluids with low viscosities and high-pressure differences over the external gear pump. Furthermore, he observed unexpected zones with a high residence time in the entry channel of the external gear pump.

The extra information obtained by adding the third dimension is however limited, since the axial clearance in the pump is typically extremely narrow. If the rotation speed of one of the gears is added as an unknown to the simulation, then a periodic release of contact is observed for most viscous fluids studied in this project. A comparison with experiments is performed for two EPDM's, where it appeared that a shear-rate, temperature and pressure dependence of the material properties are essential to obtain acceptable agreement with the experiments.

With his study, De Bie made a step towards understanding how fluid properties influence the output of an external gear pump. In future years, the current numerical simulations will be improved in terms of output predictions and computation time. Validation is needed with various materials in order to see for what kind of fluids, the current simulations are sufficient and when an extension is needed.

Vincent de Bie defended his thesis entitled "Performance analysis of external gear pumps in polymer extrusion" on March 11. Explore further How to optimize the process of polymer extrusion Provided by Eindhoven University of Technology Citation: Reducing production materials by performance analysis of gear pumps in polymer extrusion (2022, March 18) retrieved 21 April 2022 from https://phys.org/news/2022-03-production-materials-analysis-gear-polymer.html This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.

More from Physics Forums | Science Articles, Homework Help, Discussion

Use this form if you have come across a typo, inaccuracy or would like to send an edit request for the content on this page. For general inquiries, please use our contact form. For general feedback, use the public comments section below (please adhere to guidelines).

Please select the most appropriate category to facilitate processing of your request

Thank you for taking time to provide your feedback to the editors.

Your feedback is important to us. However, we do not guarantee individual replies due to the high volume of messages.

Your email address is used only to let the recipient know who sent the email. Neither your address nor the recipient's address will be used for any other purpose. The information you enter will appear in your e-mail message and is not retained by Phys.org in any form.

Get weekly and/or daily updates delivered to your inbox. You can unsubscribe at any time and we'll never share your details to third parties.

Medical research advances and health news

The latest engineering, electronics and technology advances

The most comprehensive sci-tech news coverage on the web

This site uses cookies to assist with navigation, analyse your use of our services, collect data for ads personalisation and provide content from third parties. By using our site, you acknowledge that you have read and understand our Privacy Policy and Terms of Use.